Development

VadaTech has developed a range of unique products to accelerate your development, simplify your testing and enable you and your customers to deploy smoothly. We have a range of ATCA blades for IPMI software development. You can do simulate shock and vibration for both front and rear ATCA blades while testing an ATCA chassis. Also, our VT000 power module enables powering a single ATCA blade during development.

ATCA Dev/Test

( close )

VT000

ATCA Power Module

  • Powers a single ATCA module
  • IPMI hardware address and parity
  • Fuse on each of the power rails
  • Enable switch
  • Connector for IPMI Bus A and B
  • Allows connection to shelf managers (such as VadaTech’s bench-top style VT007)
  • Test points
  • RoHS compliant
View product VT000 Data Sheet

VT994

2 Slot ATCA Backplane

  • AdvancedTCA Backplane
  • Dual slots
  • Base and Fabric Channels
  • IPMI version 2.0
  • RoHS compliant
View product VT994 Data Sheet

ATC002

ATCA Base and Fabric Channel Debug

  • AdvancedTCA Test and Development board
  • Routes Base and Fabric channels to the front panel for debugging
  • Form factor compliant to PICMG 3.0 R3.0 Specification
  • Dual SFP+ ports from the Fabric Ports (XAUI)
  • First Base Channel to Three Front Panel RJ-45 as egress ports
  • Second Base Channel to Three Front Panel RJ-45 as egress ports
  • RS-232 ports (IPMI, management)
  • IPMI version 2.0
  • RoHS compliant
View product ATC002 Data Sheet

VT980

2 Slot ATCA Backplane

  • AdvancedTCA Backplane
  • Dual slots
  • Full Mesh between the two slots
View product VT980 Data Sheet

ATC015

NEW

Third Generation IPMI MMC Controller For AdvancedTCA

  • Based on ARM 32-bit Cortex-M33 CPU (160MHz)
  • On board 4MB of Flash with 2.5MB of integrated SRAM
  • CPU Package size 13x13mm BGA
  • Meets all requirements per PICMG standard
  • Evaluation board for the MMC in AdvancedTCA (ATCA) form factor
  • Available tools for creating the FRU/SDR/Detailed HW description
  • Controller can manage an RTM (Rear Transition Module) per ATCA specification as well as 8 AMC
  • Controller uses less than ~0.3W when operating
  • Minimized hardware, footprint size, and power utilization.
View product ATC015 Data Sheet

ATC000

Module for Shock and Vibration Testing

  • AdvancedTCA standard form factor
  • PICMG 3.1 compliant
  • Provision for putting different mass type
    • simulate a real environment
  • Monitor the backplane and the RTM
View product ATC000 Data Sheet

ART000

RTM Module - Shock & Vibration Testing

  • ATCA Rear Transition standard form factor
  • PICMG 3.1 compliant
  • Module has provision for putting different mass type to simulate a real environment
View product ART000 Data Sheet

ATC001

Complete ATCA IPMI Test Suite

  • Capture and store I2C bus data
  • Analyzer mode
  • Exerciser mode
  • Compliance test mode
  • Graphical User Interface (GUI)
  • Field-upgradable firmware
  • Two 10/100 Mbit Ethernet ports routed to the front panel or to zone 2
  • Option for VadaTech VT028 for evaluation and testing
  • Option for VadaTech VT027 for evaluation and testing
  • VT027 option allows four NXP LPC2138’s to be programmed at a time
  • IPMI 2.0 compliant
View product ATC001 Data Sheet

VT007

ATCA Bench-Top Shelf Manager and/or Protocol Analyzer

  • Bench-top stand-alone Shelf Manager
  • IPMI protocol analyzer that interfaces to any ATCA and/or VPX chassis via cable
  • 3W max power with 12V input
  • Quad core ARM @ 1 GHz per core
  • 64 MB of SDRAM and 128 MB of flash
  • Dual 10/100 Ethernet Ports
  • RS-232 Debug Port
  • Field upgradable with dual boot flash
  • Telco alarms
View product VT007 Data Sheet

ATCA Dev/Test

( expand all )

VT000

ATCA Power Module

VT994

2 Slot ATCA Backplane

ATC002

ATCA Base and Fabric Channel Debug

VT980

2 Slot ATCA Backplane

ATC015

Third Generation IPMI MMC Controller For AdvancedTCA

ATC000

Module for Shock and Vibration Testing

ART000

RTM Module - Shock & Vibration Testing

ATC001

Complete ATCA IPMI Test Suite

VT007

ATCA Bench-Top Shelf Manager and/or Protocol Analyzer