with Integrated PEM and Fan Controller

  • 32-bit RISC processor @ 400 MHz
  • 64 Mbytes of DDR @ 266Mhz
  • 128 Mbytes of flash
  • Dual 10/100 Ethernet ports
  • RS-232 Debug port
  • Linux release 2.6.21
  • Field upgradable with dual boot flash
  • IPMI 2.0 compliant
  • Active/standby redundancy when utilizing two VT009s in the system
  • Rich set of management software (refer to the VT001 specification for all software components) such as HPI, RMCP, SNMP, CLI, HTTP, etc.
  • Integrated Intelligent Fan Controller
  • Integrated Power Entry Module (PEM)

Download Datasheet Add to Info Request

add to compare
0

The VT009 is a carrier which utilizes the VadaTech VT002 Shelf Manager. The carrier has integrated on it an Intelligent Fan Controller as well as an Power Entry Module (PEM).

When two VT009s are in the system, they operate in redundant active/standby mode. During operation one VT009 is active while the second one is synchronized in hot standby mode. The VT009 is fully hot-swappable to minimize service down time.

Each IPMI bus has a 64-byte FIFO to allow for a full IPMI packet on each I2C bus so there is no packet loss during operation.

The VT009 can also run as a protocol analyzer to monitor, inject, capture and validate I2C traffic on the Intelligent Platform Management Bus (IPMB). A Graphical User Interface (GUI) validates and displays the IPMI packets or schedules IPMI messages for injection into the shelf. The GUI application communicates with the VT009 through the Ethernet port.

Key Features
  • 32-bit RISC processor @ 400 MHz
  • 64 Mbytes of DDR @ 266Mhz
  • 128 Mbytes of flash
  • Dual 10/100 Ethernet ports
  • RS-232 Debug port
  • Linux release 2.6.21
  • Field upgradable with dual boot flash
  • IPMI 2.0 compliant
  • Active/standby redundancy when utilizing two VT009s in the system
  • Rich set of management software (refer to the VT001 specification for all software components) such as HPI, RMCP, SNMP, CLI, HTTP, etc.
  • Integrated Intelligent Fan Controller
  • Integrated Power Entry Module (PEM)
Benefits
  • Design utilizes proven VadaTech subcomponents and engineering techniques
  • Electrical, mechanical, software, and system-level expertise in house
  • Full ecosystem of front and rear boards, enclosures, specialty modules, and test/dev products from one source
  • AS9100 and ISO9001 certified company
Specifications
Specifications

Block diagram

Related Products

ATC800

48-Port GbE with 10-GbE Uplink Switch

  • AdvancedTCA open standard form factor
  • Linux operating system
  • Open Architect™ firmware 
  • Run as the Shelf Manager or Node board
  • Five front panel 10/100/1000Base-T ports
  • Nine front panel SFP ports
  • Front panel XFP egress port for 10GbE
  • GbE to Base Interface for 14 payload slots and Shelf Manager
  • Eighteen GbE ports to Zone 3 for use with an RTM
  • 10GbE Inter-Switch Link for fail-over via Zone2 fabric channel
  • PICMG 3.1 compliant
  • IEEE 802.3 compliant
  • IPMI Version 2.0 compliant
View product ATC800 Data Sheet

VT000

ATCA Power Module

  • Powers a single ATCA module
  • IPMI hardware address and parity
  • Fuse on each of the power rails
  • Enable switch
  • Connector for IPMI Bus A and B
  • Allows connection to shelf managers (such as VadaTech’s bench-top style VT007)
  • Test points
  • RoHS compliant
View product VT000 Data Sheet

VT830

6U ATCA SlotSaver Chassis with Dual Switching Shelf Managers

  • 19" rackmount 6U ATCA Chassis with integrated Switch and Shelf Manager
  • 10GbE/GbE Managed Layer 2
  • 40GbE/10GbE/GbE Managed Layer 3
  • 100G, 40G or 10G ATCA 6-slot backplane with Dual Star base and fabric (Full Mesh)
  • Split power distribution (odd slots on A1/B1,even slots on A2/B2)
  • Redundant Power supplies AC (DC or AC/DC optional)
  • Up to four AC supply at 1300W each (N+1)
  • 6 Rear Transition Module (RTM) slots
View product VT830 Data Sheet

Info request

Create a list of products to inquire about for more information or quote request.