AMC Media Converter/Network Tap, 10GbE/XAUI

  • AMC.2 compliant (XAUI based)
  • 10GbE or 1GbE via front panel SFP+ (Copper GbE SFP is allowed)
  • XAUI to the backplane
  • Media converter or straight-through between two ports
  • Ingress mirroring to third port
  • Physical layer mirroring
  • Fully Adaptive Electronic Dispersion Compensation (EDC)
  • Integrated BER Tester, and PRBS, Packet, and programmable Pattern Generation and checking
  • Compliant to applicable IEEE and INCITS specs
  • OS agnostic

Download Datasheet Add to Info Request

add to compare
0

The AMC225 is a single module, mid size (with full size option) AdvancedMCTM (AMC) based on the AMC.2 specification. The AMC225 provides two front panel SFP+ ports (10GbE or 1GbE option) and a backplane XAUI port. The physical layer connectivity between these three ports can be configured using an on-board high-speed signal matrix to create a direct connection (with or without media conversion) between any two ports plus the ability to mirror the ingress traffic on one of the ports to a third port. When mirroring is enabled, the AMC225 acts as a 10GbE network tap which can be used for critical security and monitoring applications such as network intrusion detection/prevention, performance nalytic, etc. The mirrored port causes no degradation to the direct-connected ports which continue to operate at full line rate. Since the mirroring is done at the physical level (Layer 1) rather than the Ethernet frame level (Layer 2), there is never a possibility for the AMC225 to drop a frame due to congestion as can happen with a typical Layer 2 switch mirroring port.

Key Features
  • AMC.2 compliant (XAUI based)
  • 10GbE or 1GbE via front panel SFP+ (Copper GbE SFP is allowed)
  • XAUI to the backplane
  • Media converter or straight-through between two ports
  • Ingress mirroring to third port
  • Physical layer mirroring
  • Fully Adaptive Electronic Dispersion Compensation (EDC)
  • Integrated BER Tester, and PRBS, Packet, and programmable Pattern Generation and checking
  • Compliant to applicable IEEE and INCITS specs
  • OS agnostic
Benefits
  • Design utilizes proven VadaTech subcomponents and engineering techniques
  • Electrical, mechanical, software, and system-level expertise in house
  • Full ecosystem of front and rear boards, enclosures, specialty modules, and test/dev products from one source
  • AS9100 and ISO9001 certified company
Specifications
Specifications

Block diagram

Related Products

AMC610

AMC 4 Port Gigabit Ethernet with 2.5” Disk

  • AMC.1 and AMC.3
  • Single-width, mid size (option for full size)
  • 4 Gigabit Ethernet ports via RJ-45
  • On board 2.5” disk with direct connect toPorts 2 and 3
  • PCIe Gen2 x4 lanes to Ports 4-7
  • IPMI 2.0 compliant
  • RoHS compliant
  • OS support for:
    • Linux
    • Windows
    • Solaris
    • VxWorks
View product AMC610 Data Sheet

UTC002

MicroTCA Carrier Hub, 2nd Generation

  • 400 MHz CPU with 64 MB DDR for MCMC (MicroTCA Carrier Management Controller) and Shelf Manager
  • Layer 2 managed GbE to each AMC (optional)
  • Non-blocking PCIe Gen 3 (x4), to each slot with option for SRIO or 10GbE (Layer 2 managed)
  • Redundant boot system to ensure fail-safe upgrades
  • Automatic fail-over with dual UTC002
  • SAS/SATA to each AMC (optional)
  • Telecom/GPS clock (Stratum-3)
  • Fabric clock with spread spectrum capability
  • Single module, full size per AMC.0
  • HPM.1 and IPMI 2.0 compliant
View product UTC002 Data Sheet

UTC010

MicroTCA DC Power Module, 792W

  • Dual -36VDC to -75VDC input,
  • 792W (available in 396W)
  • Hot swappable with support for power module redundancy
  • Available in MTCA.3 Conduction Cooled version
  • Dual IPMI bus
  • 32-bit RISC processor
  • Two banks of 256K flash for redundancy
  • Modules can be turned on without an MCH in the system
  • External as well as internal WDT
View product UTC010 Data Sheet

Info request

Create a list of products to inquire about for more information or quote request.