PCIe VU13P UltraScale+TM with Massive Optical I/O

  • Dual PCIe x16 FPGA
  • 72 fiber transceivers egress ports
  • Optical speed choice of 10G or 28G per link
  • Xilinx UltraScale+™ VU13P FPGA
  • Active cooling for FPGA
  • Dual x8 or single x16 lanes for direct connection to neighboring FPGA card(s)
  • Dual bank of 64-bit wide DDR4 for 32 GB total

Download Datasheet Add to Info Request

add to compare

The PCI597 is based on the Xilinx VU13P UltraScale+TM FPGA, which provides over 12,000 DSP slices, 360 Mb of UltraRAM and 3,780K logic cells. The Unit provides active cooling of the FPGA making it appropriate for power-hungry applications or those requiring temperature stability for good performance. The FPGA has interface to dual DDR4 memory channels (dual bank of 64-bit wide, 32 GB total). This allows for large buffer sizes to be stored during processing as well as for queuing the data to the host.

Front panel I/O is via six Board-Mount Optical Assemblies, each providing 12 channel full-duplex transceivers with Clock Data Recovery (CDR*) and fiber I/O via MTP/MPO. Transceivers are available in two speed grades, 10.6 Gb/s and 28.1 Gb/s per channel, both with multi-rate capability. The 10.6 Gb/s can drive 100 m over OM3 MM Fiber and 28.1 Gb/s can drive 100 m over the OM4 MM Fiber. The high number of egress ports allows the single FPGA to be the central point of data gathering.

The PCI597 has x16 PCIe edge connector routed to the FPGA PCIe Gen3 hard IP block. Further, the module has an addition PCIe x16 hard core which takes a second PCIe x16 slot in the chassis that allows pushing/pulling data into the host as an aggregated x32 PCIe. See PCI124 for details

Reference Design

VadaTech provides a reference design implementation for our FPGAs, complete with VHDL source code and configuration binaries. The reference design focuses on the I/O ring of the FPGA to demonstrate low-level operation of the interconnections between the FPGA and other circuits on the board and/or backplane. It is intended to prove-out the hardware for engineering/factory diagnostics and customer acceptance, and can be used as a starting point for developing an end application.

*CDR applies only to the 28G optics not the 10G optics

Key Features
  • Dual PCIe x16 FPGA
  • 72 fiber transceivers egress ports
  • Optical speed choice of 10G or 28G per link
  • Xilinx UltraScale+™ VU13P FPGA
  • Active cooling for FPGA
  • Dual x8 or single x16 lanes for direct connection to neighboring FPGA card(s)
  • Dual bank of 64-bit wide DDR4 for 32 GB total
Benefits
  • Based on the widely-used VadaTech PCI592/PCI595
  • Strong BSP support and example code to support system bring-up
  • Electrical, mechanical, software, and system-level expertise in house
  • Full system supply from industry leader
  • AS9100 and ISO9001 certified company
Specifications
Specifications

Block diagram

White Papers
Related Products

AMC592

Kintex UltraScale FPGA Carrier for FMC, AMC

  • Single module, mid-size AMC (full-size optional)
  • AMC FPGA carrier for FMC per VITA 57
  • Xilinx UltraScale™ XCKU115 FPGA
  • Supported by DAQ Series™ data acquisition software
  • AMC Ports 12-15 and 17-20 are routed to the FPGA for direct FPGA to FPGA board communication
  • AMC Ports 4-11 are routed to FPGA per AMC.1, AMC.2 and AMC.4 (protocols such as PCIe, SRIO, 1/10/40GbE, etc. are FPGA programmable)
  • Two banks of 64-bit wide and a single bank of 32-bitwide DDR4 for a total of 20 GB
  • AMC FCLKA, TCLKA, TCLKB, TCLKC and TCLKD are routed
View product AMC592 Data Sheet

FMC223

FMC High-speed DAC 14-bit at 2.5 GSPS Module

  • FPGA Mezzanine Card (FMC) per VITA 57
  • Single module  AD9739 DAC 14-bit at 2.5 GSPS
  • 2 Vpp differential Analog output swing
  • Programmable DSP clock
  • Dynamic performance
    • 8 QAM carriers @ 400 MHz IF –71 dBc
    • 16 QAM carriers @ 400 MHz IF –68 dBc
    • 32 QAM carriers @ 400 MHz IF –65 dBc
    • 72 QAM carriers @ 600 MHz IF –61 dBc
  • Single tone NSD @ 2.4 GSPS
    • 166 dBm/Hz @ 100 MHz IF
    • 162 dBm/Hz @ 1 GHz IF
  • Connection via MMCX for Analog Out and Reference Clock Input
  • Connection via LVDS for TRIG In/Out and GPIO
  • RoHS compliant
View product FMC223 Data Sheet

FMC229

FMC Quad DAC 16-bit @ 2.8 GSPS with Quadrature Modulator

  • FPGA Mezzanine Card (FMC) per VITA 57
  • Single DAC39J84
    • Quad DAC16-bit @ 2.8 GSPS
    • JESD204B
    • Wideband Digital Quadrature Modulator Correction
    • Digital Summation of Independent Complex Signals
    • Independent Complex Mixer with 48-bit NCO or +/-nxFs/8
    • Selectable 1x-16x Interpolation
  • On board dual Wideband Quadrature Modulator
  • Trig In/Output
  • RoHS compliant
View product FMC229 Data Sheet

Info request

Create a list of products to inquire about for more information or quote request.